Change Oil By Quality - Use Lubricants Scientifically

The Significance of Change OIl by Quality

Lubrication is very important for mechanical equipment, but many enterprises change oil on schedule, the oil change mode have following disadvantages, waste lubricant oil, shorten the maintenance cycle and service life of the equipment, worst of all, make the equipment scrapped. However, change oil by quality have great advantages, save oil, make the equipment in good operating condition, and creat huge economic benefits for enterprises.

 How to do change oil by quality

 Leaders’ concern

We can get support of Human, material and financial resources from leaders’ concern,  then can develop various rules and regulations that beneficial to lubrication management, with support of advanced technology and great attention of departments, make each department work more harmonious.

Assisn specific person to manage

 Change oil by quality is an highly technical work, the specific person can well managed lubricant oil of the equipments(machinery, electronic, chemical engineering),set up the archives, ensure the efficient operation of the equipments, doing statistics, analysis, sumary and master the operation state of each equipment.

Rapid test method


By using rapid test method of oil quality.If conditions permit, the enterprise can build a laboratory or equipment lubrication station of oil quality analysis, a series of equipments must be applied, such as Atomic emission spectrometer, viscometer, ferrometer, particle counter and so on.If the conditions not permit, we can equiped with viscometer and rapid oil quality analyzer, if the company don’t have a professional test site, then we just need an rapid oil quality analyzer.As long as appoint assisn specific person to manage, we will master the state of oil for each equipment.

Advantages of lubricant oil quality analyzer

Preventing the equipment from being damaged in advance once found fake and inferior oil.It’s big difference between fake oil and normal oil on test result, especially determined rapidly of water content in oil.
Avoiding change the oil while it very clean, the test result shows obviously of clean oil, short time used oil or low utilization oil.So it will save a lot of oil.

Rapid test contaminant and water percentage in oil within 3 minutes.
Detecting whether have metal particles in oil beyond 60um.
Determining the new purchased lubricant is qualified or not.
Maximisation and safe extension of intervals between oil changes.
The early detection and prevention combination of mechanical failure.
Avoidance of unnecessary engine damage resulting from overly used lubricants. 
Reduce the number of costly and unnecessary laboratory analysis of oil Samples. 

评论

发表评论

此博客中的热门博文

Lubrication System

图片
  www.checkoil.com Lubrication System Problem Diagnosis To troubleshoot an engine lubricating system,begin by gathering information on the problem.Ask the operator questions.Analyze the symptoms using your understanding of system operation.You should arrive at a logical deduction about the cause of the problem. The four problems most often occur in the lubrication system are as follows: 1.High oil consumption ( oil  must be added frequently ) 2.Low oil pressure ( gauge reads low, indicator light glows,or abnormal engine noises ) 3.High oil pressure ( gauge reads high,oil filter swelled ) 4.Defective indicator or gauge circuit ( inaccurate operation or readings ) When diagnosing these troubles,make a visual inspection of the engine for obvious problems.Check for oil leakage,disconnected sending unit wire,low oil level,damaged oil pan,or other troubles that relate to the symptoms. High Oil Consumption If the operator must add oil frequently to the engine,this is a sympto
阅读全文

What are the special diesel oil purification equipment for oil storage tank of the drilling team?

图片
                               http://www.checkoil.com/THY-310B.htm THY-310B diesel oil purifier series are developed by TIANHOU CLEAN ENERGY, which is mainly applied to large diesel generating units or other equipments powered by diesel fuel engine of medium power below 4000HP.  Technical Specs: The size of vat（mm）：800×620×570 The size of input and output oil tube：Rc1/2 Rated flux：0～200L/min   Rated pressure：200KPa   Weight：107kg Main Functions: 1. Filtering more than 90% harmful impurities in diesel fuel 2. Drawing off more than 95% water in diesel fuel 3. Reducing vehicle emissions up to 20% to 60% 4. Diesel fuel consumption reduced by 5% to 10% Product Features: 1. No shutdown is required for the replacement of filter score 2. The filtration efficiency, filtration precision and contaminant-containing capacity are simultaneously improved by the use of double-level filtration filter core 3. More than 90% of the colloid, the pitch and the mechanical impurity in
阅读全文